This is great green backlight LCD display. It is fantastic for Arduino based project. This LCD1602 LCD Display is very easy to interface with Arduino or Other Micro-controllers.

This display overcomes the drawback of LCD 1602 Parallel LCD Display in which you’ll waste about 8 Pins on your Arduino for the display to get working. Luckily in this product, an I2C adapter is directly soldered right onto the pins of the display. So all you need to connect are the I2C pins, which shows a good library and little of coding.

The I2C is a type of serial bus developed by Philips, which uses two bidirectional lines, called SDA (Serial Data Line) and SCL (Serial Clock Line). Both must be connected via pulled-up resistors. The usage voltages are standard as 5V and 3.3V.

If you already have the I2C adapter soldered onto the board like in this product, the wiring is quite easy. You should usually have only four pins to hook up. VCC and GND of course. The LCD display works with 5 Volts. So we go for the 5V Pin.

The values shown on the display can be either a simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing.

Specifications & Features :-

• Arduino IIC/I2C interface was developed to reduce the IO port usage on Arduino board
• I2C adapter allows flexibility in connections
• I2C Reduces the overall wirings.
• 16 characters wide, 2 rows
• Black text on the Green background
• Single LED backlight included can be dimmed easily with a resistor or PWM.
• Interface: I2C
• Interface Address: 0x27
• Character Color: Black
• Backlight: Green
• Supply voltage: 5V

TechnoSam’s 1602 (16×2) LCD Display with I2C/IIC Interface: Bring Your Project’s Vision to Life!

Looking for a crystal-clear and easy-to-use LCD display for your next project? Look no further than TechnoSam’s 1602 (16×2) LCD Display with I2C/IIC Interface! This versatile display boasts 16 characters per line and 2 lines, offering ample space to showcase information on your Arduino, Raspberry Pi, or other microcontroller projects.

Technical Specifications:

• Display Type: 16×2 Character LCD Display
• Interface: I2C/IIC (Inter-Integrated Circuit) for simplified communication with minimal pins required

• Backlight: Blue or Green (depending on model) for excellent visibility even in low-light conditions
• Power Supply: 5V DC
• Operating Temperature: 0°C to +50°C

Why Choose TechnoSam’s 1602 LCD Display with I2C?

• User-Friendly I2C Interface: The I2C interface allows for easy connection using only a few wires, freeing up valuable GPIO pins on your microcontroller.
• Clear and Crisp Display: Enjoy exceptional readability with the high-contrast characters and backlight.
• Perfect for Beginners and Experts Alike: Whether you’re a seasoned programmer or just starting your journey in electronics, this display’s simplicity and functionality make it ideal for various projects.
• Cost-Effective Solution: Get high-quality performance at a competitive price, making it a budget-friendly choice for hobbyists and professionals.

How to Use:

The 1602 LCD Display communicates with your microcontroller through a series of commands.

Numerous libraries are available for popular platforms like Arduino, simplifying the process of displaying text, numbers, and even custom characters.

Explore Endless Possibilities with IoT Projects:1602 LCD Display with I2C

• Informative Dashboards: Display sensor readings, status updates, and user prompts on your projects.
• Interactive Displays: Create user interfaces for controlling devices or making selections.
• Data Logging: Showcase real-time or historical data on your LCD for monitoring purposes.
• DIY Gadgets: Build custom weather stations, clocks, or information displays.

Unlock a world of visual communication with TechnoSam’s 1602 (16×2) LCD Display with I2C/IIC Interface! Order yours today and start creating!

Package Includes:-

1 x 1602 LCD Display with I2C – Blue Backlight

Original JHD 16×2 Character LCD Display With Blue Backlight If you want to add some visual output to your Arduino projects, you’ll need a display. If you need only a little to display, the LCD 16×2 Parallel LCD Display is a quite good solution.

This is the great yellow backlight LCD display. It is fantastic for Arduino based project. This LCD 16×2 Parallel LCD Display with Yellow Backlight is very easy to interface with Arduino or Other Microcontrollers.This is LCD 16×2 Parallel LCD Display that provides a simple and cost-effective solution for adding a 16×2 Black on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line display has a very clear and high contrast black text upon a yellow background/backlight.

The values shown on the display can be either simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing.

For more displays click below,

LED/LCD Display

Note: This is a genuine JHD Display as there are many fake JHD Displays in the Market.

Features :

1. 16 characters wide, 2 rows
2. Black text on the yellow background
3. Single LED backlight included can be dimmed easily with a resistor or PWM.
4. Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used)

Package Includes :

1 x JHD 16×2 Character LCD Display With Yellow Backlight

This is great green backlight LCD display. It is fantastic for Arduino based project. This LCD1602 LCD Display is very easy to interface with Arduino or Other Micro-controllers.

This 1602 lcd display with i2C IIC interface green display overcomes the drawback of LCD 1602 Parallel LCD Display in which you’ll waste about 8 Pins on your Arduino for the display to get working. Luckily in this product, an I2C adapter is directly soldered right onto the pins of the display. So all you need to connect are the I2C pins, which shows a good library and little of coding.

The I2C is a type of serial bus developed by Philips, which uses two bidirectional lines, called SDA (Serial Data Line) and SCL (Serial Clock Line). Both must be connected via pulled-up resistors. The usage voltages are standard as 5V and 3.3V.

If you already have the I2C adapter soldered onto the board like in this product, the wiring is quite easy. You should usually have only four pins to hook up. VCC and GND of course. The LCD display works with 5 Volts. So we go for the 5V Pin.

The values shown on the display can be either a simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing.

Specifications & Features :- 1602 lcd display with i2C IIC interface green

• Arduino IIC/I2C interface was developed to reduce the IO port usage on Arduino board
• I2C adapter allows flexibility in connections
• I2C Reduces the overall wirings.
• 16 characters wide, 2 rows
• Black text on the Green background
• Single LED backlight included can be dimmed easily with a resistor or PWM.
• Interface: I2C
• Interface Address: 0x27
• Character Color: Black
• Backlight: Green
• Supply voltage: 5V

Package Includes:-

1 x 1602 (16×2) LCD Display with I2C/IIC interface – Green Backlight

PCA9685 16 Channel 12 Bit PWM Servo Motor Driver,  If you want to make a robot which has lots of moving parts or if you want to control too many LEDs with PWM outputs,  then the limited PWM outputs of your microcontroller would be a big problem for you. To overcome this problem, the only thing you should do is to get a PCA9685 16 Channel 12 Bit PWM Servo Motor Driver.

You can control 16 free-running PWM outputs with 16-Channel 12-Bit PWM/Servo Driver using only 2 pins. You can even chain up 62 breakouts to control up to 992 PWM outputs.

PCA9685 16 Channel 12 Bit PWM Servo Motor Driver an I2C-controlled PWM driver with a built-in clock. That means you do not need to continuously send it to signal to tie up your microcontroller, it is completely free running!

It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs. This is good when you want to control white or blue LEDs with 3.4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single I2C bus, a total of 992 outputs.

Features :

1. Adjustable frequency PWM up to about 1.6 KHz
2. 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
3. Configurable push-pull or an open-drain output
4. The output enable pin to quickly disable all the outputs
5. Terminal block for power input
6. Reverse polarity protection on the terminal block input
7. Green power-good LED
8. 3 pin connectors in groups of 4 so you can plug in 16 servos at once
9. Chainable design
10. A spot to place a big capacitor on the V+ line
11. 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
12. This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.

Package Includes :

The TM1638 Button Digital LED Display Module is used in chip TM1638, a collection of these three common MCU peripheral circuit, the biggest feature just takes three microcontroller IO port to drive, do not need to scan display and key scanning microcontroller intervention, only need to read the relevant register send display data or test button, save MCU resources.

We usually use an external microcontroller 8 LED, 8 digital tubes, eight keys which will occupy the number of IO ports, far more than three IO mouth it, but with this module can be achieved. The practical application of key sensitive display good results. TM1638 digital tube drive chip to drive a common cathode LED digital tube. TM1638 Button Digital LED Display Module Wiring: VCC GND connected to 5V power supply, STB CLK DIO connected microcontroller IO port. The module comes with 8 buttons, 8 LED, 8 digital tube, common cathode LED digital tube, such as STC microcontroller can be directly connected

Features:

1. Use TM1638 digital tube drive chip to drive a common cathode LED digital tube.
2. Can be extended to 3 * 8 buttons, led digital tube and can be controlled separately.
3. Support 8 brightness control, led digital tube and use the same brightness.
4. Support cascading up to 6 of the same module.
5. Wiring: VCC GND connected the 5V power supply, STB CLK DIO connected microcontroller IO port.
6. 8 LED, 8-bit digital tube and 8 buttons, common cathode LED digital tube, such as STC microcontroller can be directly connected

Package Includes:1 x TM1638 Button Digital LED Display Module

Original JHD 16×2 Character LCD Display With Yellow Backlight If you want to add some visual output to your Arduino projects, you’ll need a display. If you need only a little to display, the LCD 16×2 Parallel LCD Display is a quite good solution.

This is the great yellow backlight LCD display. It is fantastic for Arduino based project. This LCD 16×2 Parallel LCD Display with Yellow Backlight is very easy to interface with Arduino or Other Microcontrollers.This is LCD 16×2 Parallel LCD Display that provides a simple and cost-effective solution for adding a 16×2 Black on RGB Liquid Crystal Display into your project. The display is 16 character by 2 line display has a very clear and high contrast black text upon a yellow background/backlight.

The values shown on the display can be either simple text or numerical values read by the sensors, such as temperature or pressure, or even the number of cycles that the Arduino is performing.

For more displays click below,

LED/LCD Display

Note: This is a genuine JHD 16×2 Character LCD Display With Yellow as there are many fake JHD Displays in the Market.

Features :

1. 16 characters wide, 2 rows
2. Black text on the yellow background
3. Single LED backlight included can be dimmed easily with a resistor or PWM.
4. Can be fully controlled with only 6 digital lines! (Any analog/digital pins can be used)

Package Includes :

1 x JHD 16×2 Character LCD Display With Yellow

The module is a 12-foot clock with four common anode tube (0.36 inch) display module for driver IC TM1637, only two signal lines can make the MCU control four 7-segment digital tubes.

Features : TM1637 4 Bits Digital Tube LED Display Module With Clock Display for Arduino

1. Ease to use.
2. Ease of multiplexing.
3. Can use as a 4 digit display unit.
4. Can use as a clock display.
5. DIY clock project.
6. 4 digit display unit.
7. Electrical/Electronic projects.
8. The counter project using 7 segment display.
9. 4 M2 screws positioning holes for easy installation

Package Includes :

One thing to note is, this meter has 2 wiring harnesses.

One harness is to provide power for the meters, that’s the 2 poles with a RED and a BLACK lead.  Dual DC 100V 100A Voltmeter Ammeter Without Shunt Small size, portable, the magnitudes of voltage and current are displayed on the same screen at the same time.

This can be supplied anywhere from 6 volts DC up to 30 VDC. This is a separate power supply that is isolated from the source, it is possible to use the same supply but it seems to affect the amp meter reading.

The 3 wire harness is used for a ground that connects directly to the battery or supply ground of the load.

Features : Dual DC 100V 100A Voltmeter Ammeter Without Shunt

1. It measures up to 100V and 100A DC.
2. Very handy and small in size.
3. It requires a power supply of 5V.
4. 100% Brand new and high quality.

Package Includes:

1 x Dual DC 100V 100A Voltmeter Ammeter Without Shunt (Dual LED Panel Ampere Voltage Meter).

Features:

1. 3mm Round Water Clear LED Lamp
2. For LED light, indication, illumination
3. Viewing angle: 40 degree
4. UV resistant epoxy
5. With lowest power consumption, long life, and super bright

Package Includes:

10 x 3mm Multicolor DIP LED.

Features:

1. 5mm Round Water Clear LED Lamp
2. For LED light, indication, illumination
3. Viewing angle: 40 degree
4. UV resistant epoxy
5. With lowest power consumption, long life, and super bright

Package Includes:

10 x 5mm Multicolor DIP LED.