0
0 items
₹0.00
No products in the cart.
HX1838 VS1838 NEC Infrared IR Remote Control Sensor Module For Arduino
Out of stock
- Crystal: the oscillation frequency of 455.
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000.
- Photo-detector and preamplifier in one package.
- Internal filter for PCM frequency.
- Improved shielding against EMI.
- Don’t forget to add CR2025 Battery to your Cart as this remote does not come with a battery
Add to Wishlist
Add to Wishlist
IR Remote Control (Without Battery)
Out of stock
- Remote control distance: more than 8 meters
- Crystal: the oscillation frequency of 455
- IR carrier frequency: 38KHz
- Output form: Digital
- Power Supply: CR2032 Battery
- Pointing Angle: up to 60º
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click
Add to Wishlist
Add to Wishlist
Black IR Remote Control Without Battery
In Stock
- Remote control distance: more than 8 meters
- Crystal: the oscillation frequency of 455
- IR carrier frequency: 38KHz
- Output form: Digital
- Power Supply: CR2032 Battery
- Pointing Angle: up to 60º
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click
Add to Wishlist
Add to Wishlist
IR Remote Control without Battery
In Stock
- Remote control distance: more than 8 meters
- Crystal: the oscillation frequency of 455
- IR carrier frequency: 38KHz
- Output form: Digital
- Power Supply: CR2032 Battery
- Pointing Angle: up to 60º
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click
Add to Wishlist
Add to Wishlist
NRF24L01 2.4GHz PA+LNA SMA Wireless Transceiver Module with Antenna
In Stock
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km
- Antenna Gain (peak): 2Dbi.
- 2MB rate (Open area): 520m.
- 1MB rate (Open area): 750m.
- 250Kb rate (Open area): 1100m.
- It uses 2.4GHz global open ISM band, with license free.
- SPI interface facilitates the communication with MCU I/O port.
Add to Wishlist
Add to Wishlist
PN532 NFC RFID Read and Write Module V3 Kit
In Stock
- Module Size: 42.7mm x 40.4mm x 4mm
- Easy to change mode: with a small SMD toggle Switch, it becomes very easy to change among IIC, SPI and HSU modes
- Longer distance: the reading distance becomes 5~7cm, compared with 4~6 cm of last version
- Built in PCB Antenna, with 5cm~7cm communication distance
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
- Work as RFID reader/writer
- Work as 1443-A card or a virtual card
Add to Wishlist
Add to Wishlist
16 Channel 5V Relay Module with Optocoupler
In Stock
- 5V relay with AC contact capacity of 10A 250V and optocoupler protection.
- Onboard power supply module does not need an external power supply. I / O port driver is active low.
- The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
- It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
- The 1-16 road can be any full on/off or any road.
- All interfaces can be directly connected through the terminal leads, very convenient.
Add to Wishlist
Add to Wishlist
8 Channel 5V Relay Module with Optocoupler
In Stock
- Channel: 8 channel
- Relay Operating Voltage: 5V
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
Add to Wishlist
Add to Wishlist
4 Channel 5V Relay Module with Optocoupler
In Stock
- 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED’s for Relay output status.
Add to Wishlist
Add to Wishlist
2 Channel 5V Relay Module with Optocoupler
In Stock
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
Add to Wishlist
Add to Wishlist
1 Channel 5V Relay Module with Optocoupler
In Stock
- Channel: 1 channel
- Relay Voltage: 5V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
Add to Wishlist
Add to Wishlist
SW 520 Tilt Vibration Sensor Module
In Stock
- Product Type: SW-520 Tilt Sensor Module
- Comparator IC used: LM393
- Output type: digital
- PCB dimension: 32mm x 14mm
- Package contains: 1 x SW-520 Tilt Vibration Sensor Module
Add to Wishlist
Add to Wishlist
ESP01 ESP8266 Serial WIFI Wireless Transceiver Module
In Stock
- Wireless Standard: IEEE 802.11 b/g/n
- Operating Voltage: 3.3V
- Serial Interface: UART
- Data Rate: Up to 72.2 Mbps
- Dimensions: Compact form factor for easy integration
Add to Wishlist
Add to Wishlist
PCF8591 Module Analog to Digital / Digital-Analog Converter Module with F-F Jumper Wire
Out of stock
- Module chip using PCF8951
- Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v)
- The module integrated photoresistor by AD collection precise value of the ambient light intensity
- Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition
- Module integrated 1 channel 0-5V voltage input acquisition (the blue potentiometer to adjust the input voltage)
- Modules with power indicator (for the module power supply indicator lights)
- Modules with DA output indicator, when the module DA output interface voltage reaches a certain value, will be lit panel the DA output indicator, the higher the voltage, the more obvious indicator brightness
Add to Wishlist
Add to Wishlist
16 Channel Analog/Digital Multiplexer Module
In Stock
- 2V to 6V operation
- “On” resistance: 70 Ohms @ 4.5V
- 6ns break-before-make @ 4.5V
- Wide operating temperature range: -55C to 125C
Add to Wishlist
Add to Wishlist
Digital Ammeter Voltmeter With Shunt
In Stock
- Operating Voltage: 5V DC.
- Current Consumption: <60mA
- Testing Voltage: 0-100V
- Testing Current: 1-100A
- Easy to read even in dim light
Add to Wishlist
Add to Wishlist
Product categories
- Arduino Boards (19)
- Drone Parts (41)
- Arduino (19)
- Dispaly Modules (44)
- Development Boards & Kits (38)
- Electronics Components (207)
- Raspberry Pi (12)
- Electronics Modules (174)
- ESP Dev Boards (9)
- Wires and Cables (48)
- Motors Drivers and Actuators (81)
- 3D Printed Parts (24)
- Sensors & Modules (218)
- Relay Boards (11)
- Sensors Modules (217)
- IoT & Wireless (78)
Filter by price
Cart
TechnoSam – Empowering the IoT Future
India’s premier destination for IoT Sensor Module Development Boards and Robotics solutions. Shop from India’s trusted Online Store: Arduino, NodeMCU, ESP32, Sensors, Modules Raspberry Pi, Relay the largest collection of IoT components we are committed to revolutionizing the technological landscape with innovation, excellence, and unwavering dedication.
Need Help?
(+91) 7030 10 3620 / (+91) 20 610 96 846
Monday – Friday: 10:00 am – 06:00 pm
Saturady: 11:00 am – 05:00 pm
Sunday Support available from Support Center Click Here
Customer Service
- Free delivery for all orders over ₹1,000