- New Launch Offer! Mini 35% Off On Products....
- Free shipping on orders above ₹ 1,000/-
₹0.00
TechnoSam's 3D Printing Services
✅ Ultra Fast Production : Get your prints ready in Just less then 12 hrs.
✅ Rapid Delivery : Delevery in Same day to 2 working days.
✅ High-Precision Printing: Perfect for functional prototypes or final-use parts.
✅ Wide Range of Materials: PLA, ABS, Nylon, TPU, Resin & more.
✅ Affordable Pricing: Competitive rates for one-off prints and bulk orders.
✅ Trusted by 500+ Clients: Engineers, makers, businesses & students across India.
✅ Free Design Review: We’ll check your file for printability and recommend improvements.
1 Channel 5V Relay Module Black
- Channel: 1 channel
- Relay Voltage: 5V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
RC522 RFID 13.56MHZ Reader Writer Module
- Voltage: DC 3.3V (Do not use 5V supply)
- Operating Current :13-26mA
- Idle Current :10-13mA
- Operating Frequency: 13.56MHz
- Highly integrated analog circuitry to demodulate and decode responses
- Supports ISO/IEC 14443 A/MIFARE
- Typical operating distance in reading/Write mode up to 50 mm
5V 1 Channel Relay Module Infrared IR Remote Switch Control
- DC 5V Home lighting system
- Remote control switch
- Smart Home / Home Automation
- Garage Door
- Remote controlled gates
- Security Monitoring
- LED lighting
- Fluorescent lamp
HX1838 VS1838 NEC Infrared IR Remote Control Sensor Module For Arduino (Copy)
- Crystal: the oscillation frequency of 455.
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000.
- Photo-detector and preamplifier in one package.
- Internal filter for PCM frequency.
- Improved shielding against EMI.
- Don’t forget to add CR2025 Battery to your Cart as this remote does not come with a battery
HX1838 VS1838 NEC Infrared IR Remote Control Sensor Module For Arduino
- Crystal: the oscillation frequency of 455.
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000.
- Photo-detector and preamplifier in one package.
- Internal filter for PCM frequency.
- Improved shielding against EMI.
- Don’t forget to add CR2025 Battery to your Cart as this remote does not come with a battery
IR Remote Control (Without Battery)
- Remote control distance: more than 8 meters
- Crystal: the oscillation frequency of 455
- IR carrier frequency: 38KHz
- Output form: Digital
- Power Supply: CR2032 Battery
- Pointing Angle: up to 60º
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click
Black IR Remote Control Without Battery
- Remote control distance: more than 8 meters
- Crystal: the oscillation frequency of 455
- IR carrier frequency: 38KHz
- Output form: Digital
- Power Supply: CR2032 Battery
- Pointing Angle: up to 60º
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click
IR Remote Control without Battery
- Remote control distance: more than 8 meters
- Crystal: the oscillation frequency of 455
- IR carrier frequency: 38KHz
- Output form: Digital
- Power Supply: CR2032 Battery
- Pointing Angle: up to 60º
- Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click
NRF24L01 2.4GHz PA+LNA SMA Wireless Transceiver Module with Antenna
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Power-down mode current: 4.2uA.
- Operating Range: 1Km
- Antenna Gain (peak): 2Dbi.
- 2MB rate (Open area): 520m.
- 1MB rate (Open area): 750m.
- 250Kb rate (Open area): 1100m.
- It uses 2.4GHz global open ISM band, with license free.
- SPI interface facilitates the communication with MCU I/O port.
PN532 NFC RFID Read and Write Module V3 Kit
- Module Size: 42.7mm x 40.4mm x 4mm
- Easy to change mode: with a small SMD toggle Switch, it becomes very easy to change among IIC, SPI and HSU modes
- Longer distance: the reading distance becomes 5~7cm, compared with 4~6 cm of last version
- Built in PCB Antenna, with 5cm~7cm communication distance
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
- Work as RFID reader/writer
- Work as 1443-A card or a virtual card
16 Channel 5V Relay Module with Optocoupler
- 5V relay with AC contact capacity of 10A 250V and optocoupler protection.
- Onboard power supply module does not need an external power supply. I / O port driver is active low.
- The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
- It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
- The 1-16 road can be any full on/off or any road.
- All interfaces can be directly connected through the terminal leads, very convenient.
8 Channel 5V Relay Module with Optocoupler
- Channel: 8 channel
- Relay Operating Voltage: 5V
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
4 Channel 5V Relay Module with Optocoupler
- 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED’s for Relay output status.
2 Channel 5V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
1 Channel 5V Relay Module with Optocoupler
- Channel: 1 channel
- Relay Voltage: 5V
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
Recently Viewed Products
PETG 3D Printer Filament (Virtual) – White
- Virtual Filament (Only for 3D Printer Subscription)
- Consistently High Quality and durable prints
- 10 times stronger than regular PLA on the market
- Deliver exceptional performance and printing smoothness
- Made from great, high-performance materials for professional prints
- Ready to print with any 3D Printer Subscription plan you take
MQ135 Air Quality Gas Sensor Module
- Sensitivity to Ammonia, Sulphide and Benzene steam
- Sensitive for benzene, alcohol, smoke
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Output voltage boosts along with the concentration of the measured gases increases.
PETG 3D Printer Filament (Virtual) – Red
- Virtual Filament (Only for 3D Printer Subscription)
- Consistently High Quality and durable prints
- 10 times stronger than regular PLA on the market
- Deliver exceptional performance and printing smoothness
- Made from great, high-performance materials for professional prints
- Ready to print with any 3D Printer Subscription plan you take
Get our emails for info on new items, sales and much more.
Register now to get latest updates on promotions & coupons. Don’t worry, we not spam!


TechnoSam – Wired for Innovation. Built for Reliability.
At TechnoSam, we specialize in providing high-quality electronics modules, development boards, and IoT components for makers, developers, educators, and enterprises. Whether you’re building a prototype or scaling to production, our curated inventory and expert support help you bring your ideas to life — reliably and affordably.
Need Help?
Monday – Friday: 10:00 AM – 05:00 PM
Saturady: 10:00 AM – 02:00 PM


















